Search
Search Criteria
Products meeting the search criteria
-25 %
SKU: RM000943
This arduino motor drive shield allows driving two channel DC motors. It uses a L298N chip which deliveries output current up to 2A each channel. The speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the mot..
₹ 599.00 ₹ 800.00
SKU: RM000032
Dual H-Bridge Power Transistor Motor Driver Arduino Board is a simple motor driver used to drive high power dc motor which is both the combination of two NPN & PNP (TIP-122 & TIP-127) transistors to operate dual motor at a time in bidirectional.Features of Dual H-Bridge Power Transistor Moto..
₹ 349.00
SKU: RM000024
The L298 dual full-bridge motor driver board for Arduino/Raspberry-pi,uses double H driver ic L298 which an integrated monolithic circuit in a 15 - lead Multi watt and Power SO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and dri..
₹ 229.00
SKU: RM001140
The Motor driver is based on the diode basis, which is a Half-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Robomart Arduino board, controlling the speed and direction of each one independently. You can al..
₹ 249.00
SKU: RM001138
The ULN2803 Stepper Motor driver is ideal for driving a stepper motor through Arduino or any other platform.Specification of ULN2803 Stepper Motor Driver Board:500mA drain per channel.Up to 50V Output Voltage.Output Clamp Diodes.Medium Power Stepper Motor Application.Applications of ULN2803 Stepper ..
₹ 299.00
SKU: RM001084
ROBOMART makes a low-cost relay board shown above that contains both the relay and the required driver circuit built using a discrete transistor. The relay coils on this relay require around 6VDC. It is easier to drive relays like this that use a lower coil voltage. The relay can switch up to 220VAC..
₹ 130.00
SKU: RM000942
The L293D is a Monolithic Integrated, High Voltage, High Current, 4-Channel Driver module. Basically you can use DC Motors and Power Supplies of up To 36 Volts, That’s Some Pretty Big Motors and the chip can supply a maximum current Of 600Ma Per Channel, The L293D Chip Is Also What’s known as a type..
₹ 199.00
SKU: RM000864
This is fully programmable 30A BLDC ESC Circuit with 5V, 3A BEC. Can drive motors with continuous 30Amp load current. It has sturdy construction with 2 separate PCBs for Controller and Electronic Speed Controller power MOSFETs. It can be powered with 2-4 lithium Polymer batteries or 5-12 NiMH / NiCd..
₹ 350.00
SKU: RM001083
ROBOMART makes a low-cost relay board shown above that contains both the relay and the required driver circuit built using a discrete transistor. The relay coils on this relay require around 6VDC. It is easier to drive relays like this that use a lower coil voltage. The relay can switch up to 220VAC..
₹ 170.00
SKU: RM000863
This is fully programmable 20A BLDC ESC with 5V, 3A BEC. Can drive motors with continuous 20Amp load current. It has sturdy construction with 2 separate PCBs for Controller and ESC power MOSFETs. It can be powered with 2-4 lithium Polymer batteries or 5-12 NiMH / NiCd batteries. It has separate volt..
₹ 380.00
SKU: RM000856
The L298 is an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, a high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are pr..
₹ 117.00
-17 %
SKU: RM001054
The 2 Channel Wired Remote Control Kit with BO motor is a very basic robot kit for students those who want to study about the behavior of motor and also to analysis the motor driving circuit. It is a very durable nature helps in acquiring expertise on basics of robotics and to understand the working..
₹ 250.00 ₹ 300.00
Showing 1 to 12 of 12 (1 Pages)